Classic Mustangs List Archive

This read-only message was archived from a public mail list.
Mail From: (email redacted) (Tim Kreps)

Hi,

I am about to add the Rocker Panel Molding (again) to my '69 Mach1. When
the body was restored the original molding was tossed and the holes filled.
Can anyone point me to where I might find the exact location of where the
Rocker Panel goes? If you know of where the exact holes should be drilled,
even better.

Regards,

Tim Kreps
Napa, CA
'69 Mach1

This read-only message was archived from a public mail list.
Mail From: (email redacted) (Wal Marshall)

Tim,

Where did you get the replacement rocker moulding from... and at what
cost?..I don't recall seeing them in any of my catalogues?

Thanks

Wal Marshall

----- Original Message -----
From: "Tim Kreps" <(email redacted)>
To: <(email redacted)>
Sent: Saturday, October 06, 2001 7:55 AM
Subject: [CM] '69 Rocker Panel molding location


> Hi,
>
> I am about to add the Rocker Panel Molding (again) to my '69 Mach1. When
> the body was restored the original molding was tossed and the holes
filled.
> Can anyone point me to where I might find the exact location of where the
> Rocker Panel goes? If you know of where the exact holes should be
drilled,
> even better.
>
> Regards,
>
> Tim Kreps
> Napa, CA
> '69 Mach1
>
> _______________________________________________
> Classic-mustangs mailing list
> (email redacted)
> mix.twistedpair.ca/mailman/listinfo/classic-mustangs
>

This read-only message was archived from a public mail list.
Mail From: (email redacted) (Karl Rotcavich)

Wal Marshall wrote:

> Tim,
>
> Where did you get the replacement rocker moulding from... and at what
> cost?..I don't recall seeing them in any of my catalogues?
>
> Thanks
>
> Wal Marshall

Wal,


The '69 Rocker Moldings are being reproduced by Dynacorn Intl. I have them in
stock at $44.00 each, if you mention the list you get a 10% discount.

"www.mustang-country.com"

Karl

>
>
> ----- Original Message -----
> From: "Tim Kreps" <(email redacted)>
> To: <(email redacted)>
> Sent: Saturday, October 06, 2001 7:55 AM
> Subject: [CM] '69 Rocker Panel molding location
>
> > Hi,
> >
> > I am about to add the Rocker Panel Molding (again) to my '69 Mach1. When
> > the body was restored the original molding was tossed and the holes
> filled.
> > Can anyone point me to where I might find the exact location of where the
> > Rocker Panel goes? If you know of where the exact holes should be
> drilled,
> > even better.
> >
> > Regards,
> >
> > Tim Kreps
> > Napa, CA
> > '69 Mach1
> >

This read-only message was archived from a public mail list.
Mail From: (email redacted) (Wal Marshall)

Thanks Karl.

Actually I'm suffering from brain fade... sorry! (Didn't notice that we
were discussing a 69 not a 70)

I was actually after the larger aluminium rocker mouldings used on the 70
Mach's..you know the ones that are about 4-5 inches high, with Mach1
impressed into the first section. Any sources for those?

Cheers

Wal

----- Original Message -----
From: "Karl Rotcavich" <(email redacted)>
To: <(email redacted)>
Sent: Saturday, October 06, 2001 4:11 PM
Subject: Re: [CM] '69 Rocker Panel molding location


> Wal Marshall wrote:
>
> > Tim,
> >
> > Where did you get the replacement rocker moulding from... and at what
> > cost?..I don't recall seeing them in any of my catalogues?
> >
> > Thanks
> >
> > Wal Marshall
>
> Wal,
>
>
> The '69 Rocker Moldings are being reproduced by Dynacorn Intl. I have
them in
> stock at $44.00 each, if you mention the list you get a 10% discount.
>
> "www.mustang-country.com"
>
> Karl
>
> >
> >
> > ----- Original Message -----
> > From: "Tim Kreps" <(email redacted)>
> > To: <(email redacted)>
> > Sent: Saturday, October 06, 2001 7:55 AM
> > Subject: [CM] '69 Rocker Panel molding location
> >
> > > Hi,
> > >
> > > I am about to add the Rocker Panel Molding (again) to my '69 Mach1.
When
> > > the body was restored the original molding was tossed and the holes
> > filled.
> > > Can anyone point me to where I might find the exact location of where
the
> > > Rocker Panel goes? If you know of where the exact holes should be
> > drilled,
> > > even better.
> > >
> > > Regards,
> > >
> > > Tim Kreps
> > > Napa, CA
> > > '69 Mach1
> > >
>
> _______________________________________________
> Classic-mustangs mailing list
> (email redacted)
> mix.twistedpair.ca/mailman/listinfo/classic-mustangs
>